CCNA考試實驗常用的命令總結

字號:


    路由器實驗:
    router> enable 從用戶模式進入特權模式
    router# disable or exit 從特權模式退出到用戶模式
    router# show sessions  查看本機上的TELNET會話
    router# disconnect 關閉所有的TELNET會話
    router# show users 查看本機上的用戶
    router# erase startupconfig刪除NVRAM中的配置
    router# reload 重啟路由器
    router# config terminal 從用戶模式進入特權模式
    router(config)# hostname rl 配置用戶名為rl
    router(config)# #banner welcome# 配置開機話語
    router# show controllers serial0查看串口0的物理層信息(主要是查看DTE/DCE)
    router# show ip interface  查看端口的IP配置信息
    router# show hosts 查看主機表
    end or ctrl+z  從各種配置模式退到特權模式
    rl(config)# no ip domainlookup 關閉動態域名解析
    rl(config)# ip domainlookup打開動態域名解析
    rl(config)# ip nameserver 202.106.0.20 打開動態域名解析之后便可以指定DNS服務
    rl(config)# interface serial 0 進入serial 0的接口配置模式
    rl(configif)# no shutdown路由器出廠默認所有端口關閉,使用此命令使它們打開
    rl(configif)# encapsulation ppp  封裝ppp
    rl(configif)# clockrate 64000  如果是DCE使需要設置時鐘速率,如果是DTE使不必
    設置
    rl(configif)# bandwidth 64 設置端口帶寬為64K
    rl(configif)# ctrl+c 或者ctrl+z 快捷鍵退出到特權模式
    rl# show interface serial 0查看s0信息,如果看到serial和 line protocol都顯
    示up,說明鏈路兩端都設置成功
    注意:如果出現serial down, line down 可能對方的端口沒有打no shutdown或者電纜沒有插好;如果出現serial up, line down 可能是DCE端沒有設置clock rate, 也可能是封裝格式不對
    rl# show cdp neighbors 查看CDP鄰居信息
    rl# show cdp entry *
    rl(configif)# ip add 10.0.0.1 255.0.0.0 進入相應的接口,配置相應的IP地址
    rl# ping 10.0.0.2  使用ping命令查看鄰居的連通性
    rl# show ip route 查看路由表,可以看到以C打頭的路由 信息,這是直連的路由信息;可以看到 R開頭的路由信息,是從rip學來的路由 信息;可看到以I開頭的路由信息取代 了以R開頭的路由信息,這是因?yàn)閕grp 的管理距離是100,小于rip的120
    rl(configif)# router rip  啟動RIP路由協議
    rl(configrouter)# network 10.0.0.0發布網段(注意network后面是接的網絡號而不是IP地址)
    rl# show ip protocol查看配置的路由協議
    rl(config)# router igrp 300一定要注意在IGRP后面加自治系統號,考試的時候題目會告訴你AS NUMBER, 照敲就是
    rl(configrouter)# network 10.0.0.0
    rl(config)# line vty0 4 進入虛擬線程配置模式,在此模式可對telnet功能進行配置
    rl(configline)# login
    rl(configline)# password cisco 配置telnet密碼,默認的網絡設備 telnet的 功能是關閉的,配了密碼之后會自動打開
    rl(config)# enable password cisco配置進入enable模式的密碼, 區分大小寫
    rl(config)# enable secret ciscocisco 配置進入enable模式的密碼,是加密的密碼,show run是看不見的
    rl(config)# line console 0
    rl(configline)# login
    rl(configline)# password cisco  配置進入用戶模式的密碼
    rl(configline)# logging synchronous  輸入同步
    rl(configline)# exectimeout 0 0禁止因?yàn)橐欢螘r(shí)間沒有輸入而跳出
    rl# copy runningconfig startupconfig  保存配置,考試的時候注意題目的要求,如果題目里要求你保存配置就一定不能少了這一項
    r1# copy tftp startupconfig
    r1# copy runningconfig tftp
    r1# copy tftp flash
    交換機實驗:
    switch(config)# ip address 192.168.0.177 255.255.255.0 與路由器在接口上的配置IP不同,交換機是在全局配置模式配置
    switch(config)# ip defaultgateway 192.158.0.1 給交換機配置一個缺省網關,請注
    意,不用寫掩碼
    switch(config)# vlan2 name cisco   配置一個vlan2并且指定名字叫CISCO
    switch# show interfaces  查看端口狀態
    switch(config)# interface e0/10  進入端口e0/10
    switch(configif)# vlanmembership static 2   將端口放進vlan2里面
    switch(config)# int f0/26  進入快速以太網端口f0/26
    switch(configif)# trunk on 啟用trunk,注意:只能在百兆以上端口啟用trunk
    switch(configif)# notrunkvlan 51 52 在主干上關閉VLAN51、52的傳輸